Synthesis of submicron CaZrO<Subscript>3</Subscript> in combustion reactions

Submicron CaZrO₃ powder is obtained in combustion reactions (solution combustion synthesis—SCS) with glycine. It is found that SCS reduces the sintering temperature of CaZrO₃ powders. The dielectric properties of calcium zirconate ceramics are studied by the electrochemical impedance method. It is shown that a ceramics of powders obtained by the SCS method has high dielectric characteristics.     

Isolation of Bisphenol A-Tolerating/degrading Shewanella haliotis Strain MH137742 from an Estuarine Environment

Applied Biochemistry and Biotechnology - The human exposure to bisphenol A (BPA) occurs frequently. Once, this compound was one of the highest volume chemicals produced worldwide and used as a...     

Compact Induction Accelerator of Laser Plasma for Ion Energy up to 1 MeV

Physics of Particles and Nuclei Letters - The collective acceleration of laser plasma ions in a rapidly increasing magnetic field (108 T/s) excited by a powerful current pulse in a low-inductive...     

Total Electron Content Measurements in the Ionosphere Disturbed by High-Power High-Frequency Waves by the Methods of Incoherent Scattering of Radio Waves and Radio Sounding by Glonass Satellite Signal

Radiophysics and Quantum Electronics - We present the results of comparing the total electron content measurements based on GLONASS satellite signals and the EISCAT UHF incoherent scatter radar...     

Evolution of a Non-Uniform Deformed State in the Structure of Zinc-Chalcogenide Cubic Crystals Doped by 3 d Ions

The real structure of bulk Zn1 – хМхSe (S) crystals of diluted magnetic semiconductors with М = V, Cr, Fe, Co, Ni 3d impurities is characterized by neutron diffraction. These impurities are known to greatly destabilize even the initial lattices of pure zinc chalcogenides. Data on the resulting non-uniform microstrain field induced by atomic displacements are obtained from the structural peaks along the tangential and radial directions on the above crystals within a dopant concentration range of 0.01 ≤ х ≤ 0.10. Additional nodes with q = (1/3 1/3 1/3) 2π/a (q is the wave vector and a is the cubic unit cell) emerging in the reciprocal lattice of the cubic structure are considered as evidence for a pre-transition to the fcc (face-centered cubic)–hcp (hexagonal close-packed) phase state, which implies transitions from the fcc lattice along an 8-ray non-Lifshitz star with the wave vector k5 = μ(b1 + b2 + b3), where b1, b2, b3 are the reciprocal lattice vectors and μ ≈ 1/3.     

Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films

Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064